Tailgate Spoiler

[NM CRV Newbie]

Greetings:

The love of my life and I just bought an '07 EX 4WD in Glacier Blue. Our first Honda. Figured it was time to retire the '95 Maxima with 214,000 miles.

Regarding the Tailgate Spoiler (which we don't have) will it help keep the rear window clean? In other words, does the air flow from the roof flow under the spoiler.

Thank you.

Sandi & John
In the mountains east of Albuquerque

[1ownerT]

I just installed mine this past weekend. There is a slight gap to either side of the center attaching point. Can air flow through? seems unlikely but the gap is there.

[RichK]

NM CRV Newbie states:
Regarding the Tailgate Spoiler (which we don't have) will it help keep the rear window clean? In other words, does the air flow from the roof flow under the spoiler

In my experience road slush and rain on the back glass are slightly less intense than before spoiler installation. You will still need to use the rear wiper occasionally.

1ownerT states:
I just installed mine this past weekend. There is a slight gap to either side of the center attaching point. Can air flow through? seems unlikely but the gap is there.

My spoiler was installed by the dealer and there is no gap between the entire edge of the spoiler and the rear hatch. On your install some air might flow through, but I wouldn't be concerned about it.

[1ownerT]

NM CRV Newbie states:
Regarding the Tailgate Spoiler (which we don't have) will it help keep the rear window clean? In other words, does the air flow from the roof flow under the spoiler

In my experience road slush and rain on the back glass are slightly less intense than before spoiler installation. You will still need to use the rear wiper occasionally.

1ownerT states:
I just installed mine this past weekend. There is a slight gap to either side of the center attaching point. Can air flow through? seems unlikely but the gap is there.

My spoiler was installed by the dealer and there is no gap between the entire edge of the spoiler and the rear hatch. On your install some air might flow through, but I wouldn't be concerned about it.

You are absolutely 100% correct, I don't know what I was thinking:confused:
There is no gap on mine either.

[anamal19]

I want one just cause it looks cool. :cool:

[2RedV's]

I have seen a few in the area with the spoiler. It looks GREAT!

[PINODY]

Got an idea, since the rear hatch is tinted on the LX, how slick would a Black spoiler look instead of body color? (match the windows and clading) any photoshop pros here?! :) ... http://www.crvownersclub.com/forums/showthread.php?t=1644 http://img292.imageshack.us/img292/4785/crvrearslantedxr2.jpg http://img292.imageshack.us/img292/5751/crvrearzl0.jpg http://www.hondasuv.com/members/attachment.php?attachmentid=12151&stc=1&d=1193787331

[Edd]

I'm also interested in a black rear sun/dust deflector for my '07EX-L, rather than the Honda-brand and related Asian knock-offs. Here's the disappointing news:

I contacted EGR about availabilty. I received an email from EGR-USA indicating that they have no intention of producing one for the 07/08 CR-V. In fact, EGR is completely ending production of their rear sun/dust deflectors altogether.

I also emailed Lund and received a vague reply indicating that they don't have anything yet available for the current generation CR-V. No info on if/when one may become available...

[c5bob]

The spoiler does not help or hurt the dirt collection on the back window . . . but it looks really cool, which is why I put one on my V. IMHO, the spoiler completes the back of the car - it looks finished now.

[stanlam]

There's somebody on this board that was going thinking about putting a Black Spoiler on a White CR-V. Did you ever do it? Can you post pictures.

I am thinking about putting a black spoiler on my Glacier Blue CR-V. I can get the part on Ebay for about $110.00 shipped. Then I can spray paint it myself for another $5.00. The reason is because Glacier Blue spray paint is hard to find, compared to black. I've seen a Lexus SUV that comes in all different colors, but the spoiler is always black.

[Cravenfan]

Going for the cool factor myself, but sold my wife on the "less dirty" point, however even if it's the same, or slightly worse, she won't know and it still looks cooler. :D

[stanlam]

Please, please show me a picture of your CR-V with the spoiler.

thanks,
stan

[Cravenfan]

:) Here is our CRV spoiler, right beside our Acadia spoiler.

[R11]

Got an idea, since the rear hatch is tinted on the LX, how slick would a Black spoiler look instead of body color? (match the windows and clading) any photoshop pros here?! :) ... 2007 Taffeta White CR-V EX-L AWD - Honda CR-V Owners Club Forums (http://www.crvownersclub.com/forums/showthread.php?t=1644) http://img292.imageshack.us/img292/4785/crvrearslantedxr2.jpg http://img292.imageshack.us/img292/5751/crvrearzl0.jpg http://www.hondasuv.com/members/attachment.php?attachmentid=12151&stc=1&d=1193787331First post on CR-V Owners Club forums (although I used to post at the Element Owners Club forums a bit a couple years ago when I was thinking about getting one). Anyway, I'm no photoshop expert, but I'll be able to show you what this looks really looks like next week. I just picked up an 08 Taffeta White EX last night and ordered the Pearl Black spoiler for it earlier in the day. It's scheduled to be delivered Monday so I'll post some pics after I mount it.

Personally, I think it will look better than the body color units. The problem I have with them is that because the tail lights go all the way up to the top of the window, the body color spoilers end up looking like they're kind of hanging out there and tacked on. Especially since they don't match the roof rails they butt up to. I think with the black spoiler the roof rails will flow right into it, and since it's the shiny pearl black it should match the reflective privacy glass of the rear window pretty well too. Well, either that or I just wasted $220 ;).


ron

[jbgulat]

i recently added the spoiler to the back of my 08 crv ex-l just for the looks. i don't think that the spoiler helps to keep back window from dirt but i've only had it for a couple of weeks.

[Black Pearl]

R11, welcome to the club and neat idea on the contrasting spoiler. Do post photos of the results. If it works for you, I am going to get a white one for the Black Pearl! (Somehow I don't think it will work as well.)

Again welcome to the club, good luck with the new V, and we will be looking forward to see how your spoiler looks.

[R11]

R11, welcome to the club and neat idea on the contrasting spoiler. Do post photos of the results. If it works for you, I am going to get a white one for the Black Pearl! (Somehow I don't think it will work as well.)

Again welcome to the club, good luck with the new V, and we will be looking forward to see how your spoiler looks.

Ah, but the theory is actually more of a Trim & Window Matching than Body Color Contrasting. As a NBP owner though you're covered either way! :) I am curious to see how it turns out. We shall see...



ron

[PINODY]

Ah, but the theory is actually more of a Trim & Window Matching than Body Color Contrasting. As a NBP owner though you're covered either way! :) I am curious to see how it turns out. We shall see...



ronWow, I remember when I posted that idea ... went to our local dealer and tried both the Black and Beige for comparison ... the rest is history! :eek: http://www.crvownersclub.com/forums/attachments/800d1204859130-img_0061.jpg

[R11]

Wow, I remember when I posted that idea ... went to our local dealer and tried both the Black and Beige for comparison ... the rest is history! :eek:

No doubt having the roof rails painted to match makes a big difference in how well integrated the body colored spoiler looks :). I like the contrasting trim and lower cladding though so for me that wasn't an option... Different strokes. That's what makes it fun!


ron

[PINODY]

No doubt having the roof rails painted to match makes a big difference in how well integrated the body colored spoiler looks :). I like the contrasting trim and lower cladding though so for me that wasn't an option... Different strokes. That's what makes it fun!


ronSorry, I meant to say/add that the Black pearl painted spoiler didn't match the Matte black roof rails - not so noticeable on a Black pearl CR-V, but very noticable on our Beige - that's why we went with beige, at least it matched something. :o

[R11]

Sorry, I meant to say/add that the Black pearl painted spoiler didn't match the Matte black roof rails - not so noticeable on a Black pearl CR-V, but very noticable on our Beige - that's why we went with beige, at least it matched something. :o


Pinody, you should have started with an LX so you could have gotten solar gold window tinting. Then you could have named it "Goldfinger" :D. Actually the roof rails aren't really matte black (vs. the lower cladding which does have a rough/matte finish). They're smooth and have more of a satin looking appearance to my eye. The privacy glass side and rear windows are definitely shiny black though :).

I installed the spoiler late last night but didn't finish up until well after dark so I couldn't get any pics to post yet, (or even any very good views of it myself). Took a few long looks at it this morning in the light before heading out to work though and I think it's going to more than meet my expectations. It ties in very nicely with the roof rail lines and finishes them off well. The main thing I was hoping to accomplish with it was to break up the somewhat too well-rounded rear end of the vehicle, without making the roof seem longer, and to avoid a tacked-on look. It seems to work pretty well for that as the spoiler doesn't look like an extension of the roof really, but rather an integrated part of the trim/window. It breaks up the rounded top, but is still fairly subtle for as much as it sticks out. As you mentioned, I too was a little apprehensive about the shinyness of the finish not matching the rails perfectly. But it's such a small point of contact between the ends there and because it matches the window which it's laying almost completely on, it looks like it will work well.

I will have to hold out ultimate judgement until I see it in direct sunlight where the difference will be most noticable, but based on what I saw this morning I really think it will be fine. I should be able to get some pics tonight to post up.


ron

[R11]

Here's a few pics of the black spoiler. The light was starting to get a little low so there's not great detail but at least you can get an idea of how it looks on the vehicle.


http://img504.imageshack.us/img504/2329/1070737ih4.jpg


http://img504.imageshack.us/img504/684/1070728pq6.jpg


http://img504.imageshack.us/img504/7380/1070725mx9.jpg

[R11]

And the rest:

http://img504.imageshack.us/img504/3450/1070746if6.jpg

http://img504.imageshack.us/img504/880/1070740sk3.jpg

http://img504.imageshack.us/img504/8223/1070742dh5.jpg



ron

[RichK]

Looks very nice! Ties in with the roof rails, rear window, and lower cladding.

[ga cr-v lady]

Yes! That definitely rocks. Looks alot like the Lexus RX black spoilers that someone mentioned in another thread. Not sure sure it would work with the Green Tea color, but it should give people more courage to take the leap after seeing yours. Thanks for the pics.

[R11]

Yes! That definitely rocks. Looks alot like the Lexus RX black spoilers that someone mentioned in another thread. Not sure sure it would work with the Green Tea color, but it should give people more courage to take the leap after seeing yours. Thanks for the pics.

After having a little time to really look at it now I think it would look good with any of the CRV colors as long as they also had the privacy glass (or any similar aftermarket tinting). I think the glossy black spoiler would probably stick out and look out of place without the dark and reflective back window to sit on. With the privacy glass though it actually blends in and matches pretty darn well. I'm really happy and glad I went ahead with it now :).


ron

[kipnita]

I wasn't sure that was going to work but it looks really nice.

I have been contemplating a spoiler for my NBP.

How difficult was the install?

I looked at the instructions and it doesn't look too bad (except for the drill holes in my new car part)!

[jpod]

I agree, that black spoiler looks pretty cool.

But I agree with kipnita--I'm uncomfortable drilling holes in my Itachi-san.

I may get one in the next few months but maybe I'll attach it with the same adhesive Honda uses on the protective shipping film.;)

[R11]

I would say that if you have any mechanical experience at all and have the tools, the install is straight forward and pretty simple. I drilled the outside holes with the hatch open using a little step ladder, and just wrapped a towel around under the hinges to catch the drilling bits and so I wouldn't have to worry about using a drill stop. Yes, it is a little disconcerting to start drilling holes in the roof of your vehicle. But if you carefully mark and lightly centerpunch for the holes, use sharp drill bits and just take your time, there's really no reason to worry. Many years ago I installed aftermarket sunroofs in a couple of my vehicles and compared to drilling a few holes, cutting out a large section of your roof with a jigsaw is a whole lot more freaky :eek:.

On the other hand, if you don't really have experience and/or the trepidation is a bit too much for you, I wouldn't think it should really cost much to have a dealer or any local mechanic you may know do the install instead. Sometimes peace of mind is well worth paying a little for too.


ron

[GreenCRV]

I did mine today. Took me around 1.5 hours (I take my time). And installed the Body Side Moldings too. After that my car looks a lot better.


The follwing link is for Tailgate Spoiler Installation :)
YouTube - Episode #60 - Honda CR-V Tailgate Spoiler Installation (http://www.youtube.com/watch?v=VDzNJ38abJo&feature=related)

[GreenCRV]

1.5 hours later.:)

1302

1303

1304

[R11]

Nice work!


ron

[X-Brawn]

Indeed, looks very sharp and nice.

I almost bought a Green Tea Metallic as I liked it better then the Glacier Blue my parents bought. But, I ended up with the gold (Borrego Beige Metallic) simply because I fell in love with the color once I saw it in person.

[kgf3076]

And the rest:
http://img504.imageshack.us/img504/7380/1070725mx9.jpgAnd a AP-2 Berlina....I'm the proud owner of a '08 Royal Blue Pearl CR-V EX and a '04 NFR AP-2. Hondas seem to run in families.

[R11]

And a AP-2 Berlina....I'm the proud owner of a '08 Royal Blue Pearl CR-V EX and a '04 NFR AP-2. Hondas seem to run in families.
My S is an '04 as well. I always liked the S2000 since it was introduced. Then when they made the alterations for the AP2 it put me over the top and I had to put in an order for the Berlina in fall of '03. I would have to say it's the most satisfying vehicle overall that I've owned in 35 years of driving.

You aren't kidding about the Honda thing. They're insidious :eek:. Prior to the S I had never owned one, but now I actually have four at the moment as there are two more in the garage... About four years ago I bought an old '85 VT700C Honda Shadow cruiser with under 10K original miles. And just recently I bought an '06 599/Hornet with only 1,800 miles.

http://img80.imageshack.us/img80/2815/1070707vx0.jpg

Now with the new additions I seriously need to get off my butt and sell the Shadow and old AWD Caravan to get some of my space back :).


ron

[kipnita]

OK, one of my weekend projects is to install the spoiler.

I've received/inspected the spoiler - paint looks nice!

When I unpacked the spoiler I located the hardware but during my review of the instructions (for the upteenth time!) I noticed the rubber seals were missing.

Shook the box again, noting else fell out....looked in the box and a small "baggy" was taped to its interior. Suprise, rubber seals found!

I have reviewed the install instuctions and the video from College Hills multiple times.

Once I locate the correct tools (and overcome my fear of drilling into my car!) it looks like this can be done in 30-45 minutes.

I'll post next week re the project....

[kipnita]

Done, looks great.

EZ to install, instructions were straight forward and watching the college hills install video really helped.

It took 1 hour start-finish.

Do not pay the dealer an inflated rate to do this job, do it yourself!

How long do you think it will take the wife to notice?????

[MQuillen]

Shook the box again, noting else fell out....looked in the box and a small "baggy" was taped to its interior. Suprise, rubber seals found!


I'll post next week re the project....

Thanks for the post, kipnita. I'd looked 3 times for the gaskets. I read your post, and found a small piece of what looked like packing tape tightly taped to the inside of the box. I'm sure a lot of these get thrown away.

[MQuillen]

Well, now I know why Honda dealers charge so much to install these things. They must bring in neurosurgeons to manipulate those paper thin, sticky, easily torn, rubber gaskets, that are almost impossible to find in the box.

The install really isn't that bad, but I really dreaded drilling into the tailgate--"Rust Never Sleeps." I touched the holes up with zinc chromate primer, let it dry, then touch-up paint, let it dry, then I scraped all of that off the center hole trying to install a stubborn jack nut. And lastly I used silicone sealent. I'm certain some nasty chemical reaction between the paint primer and silicone will nullify my rust preventive efforts, lol.

[jwv651]

Hi All, proud new owner here. I have the spoiler coming tomorrow plus the side mouldings and need some here. Question...Were did you find MM drill bits? I need the 3mm 6mm 8mm and 11mm. I have looked everywhere. Any help would be appreciated! BTW nice forum, looking forward to spending time here. ;)

Thanks Joe V

[jim.cook]

I used US sized bits that were several thousands less than the equal mm bits. Thus I used fractional and letter bits. It worked out well. Don't forget to center punch so the first drill doesn't wander. Don't push too hard because the thiskness of the steel is very thin. Let the drill do the work.

Hi All, proud new owner here. I have the spoiler coming tomorrow plus the side mouldings and need some here. Question...Were did you find MM drill bits? I need the 3mm 6mm 8mm and 11mm. I have looked everywhere. Any help would be appreciated! BTW nice forum, looking forward to spending time here. ;)

Thanks Joe V

[jwv651]

I used US sized bits that were several thousands less than the equal mm bits. Thus I used fractional and letter bits. It worked out well. Don't forget to center punch so the first drill doesn't wander. Don't push too hard because the thiskness of the steel is very thin. Let the drill do the work.Thanks Jim...Looking forward to my weekend project. Now all I need to do is convert MM to SAE.:eek:

[MQuillen]

JWV, the most important sizes to get right is the 8mm and the 11mm, since the 3mm and 6mm are just step sizes, as I'm sure you are aware. I used 1/8 for the 3mm, 3/16 for the 6mm, 5/16 for the 8mm, and 7/16 for the 11mm center hole. The 7/16 is actually 11.1 mm, and I still had a hard time getting the jacknut in the hole. These sizes work fine. Do lightly center punch, use new or newly sharpened bits, and file off all burrs. I zinc chromate primed the bare metal, and also used touch up paint over that (which is probably overkill since it's not going to be exposed). And then I used silicone sealant in and around the hole edges, in addition to the flimsy rubber seals. If it rusts it won't be because I didn't try, and I'm sure I did better than the dealer would have.

One other note, in the instructions it says to enlarge the outboard holes from the top side of the tailgate using a drill stop, and to enlarge the inboard holes from the underside of the tailgate. I think the reasoning behind this is that the outboard holes are on or near the panel seam, and it's easier to drill to size if you do it from the top. I think if you're careful it doesn't matter much. Lastly, when positioning the spoiler into the holes, it would be helpful to have two sets of hands, but it can be done without it.

I've done a lot of work on cars and it never gets mentally easier to drill holes in my brand new vehicles.

[Darren Chow]

CRVBUMPERGUARD (http://www.parts-suv.com/products/CRVBUMPERGUARD.htm)

Do you like this guard?

[jwv651]

JWV, the most important sizes to get right is the 8mm and the 11mm, since the 3mm and 6mm are just step sizes, as I'm sure you are aware. I used 1/8 for the 3mm, 3/16 for the 6mm, 5/16 for the 8mm, and 7/16 for the 11mm center hole. The 7/16 is actually 11.1 mm, and I still had a hard time getting the jacknut in the hole. These sizes work fine. Do lightly center punch, use new or newly sharpened bits, and file off all burrs. I zinc chromate primed the bare metal, and also used touch up paint over that (which is probably overkill since it's not going to be exposed). And then I used silicone sealant in and around the hole edges, in addition to the flimsy rubber seals. If it rusts it won't be because I didn't try, and I'm sure I did better than the dealer would have.

One other note, in the instructions it says to enlarge the outboard holes from the top side of the tailgate using a drill stop, and to enlarge the inboard holes from the underside of the tailgate. I think the reasoning behind this is that the outboard holes are on or near the panel seam, and it's easier to drill to size if you do it from the top. I think if you're careful it doesn't matter much. Lastly, when positioning the spoiler into the holes, it would be helpful to have two sets of hands, but it can be done without it.

I've done a lot of work on cars and it never gets mentally easier to drill holes in my brand new vehicles.Well I finally got the nerve up and installed my spoiler per your excellent instructions and it went perfect...silicone sealant and all. Thanks a bunch! What a amazing difference this made to our CR-V...it looks finished now, something was missing and the spoiler was it. Once again Thanks! :D :)

[MQuillen]

Glad you had a successful install, JWV. I agree with your assessment, I think the spoiler finishes the roofline very well.:D

[TKCRV08]

Well I finally got the nerve up and installed my spoiler per your excellent instructions and it went perfect...silicone sealant and all. Thanks a bunch! What a amazing difference this made to our CR-V...it looks finished now, something was missing and the spoiler was it. Once again Thanks! :D :)

Gotta post a pic of it for us! :-D

[Red916]

here's a question... :)

Basically, my CRV is a company car, and as such when I give it back in a couple of years I've got to return it to looking as it arrived.

I therefore have no qualms about drilling the 4 outer holes - when I take the spoiler off in the future I'll plug them if need be, and replace the end cap covers so that they can't be seen :)

BUT - obviously I can't do that with the centre hole :(

Has anyone who has fitted this got any thoughts on how it might work / how secure it might be if I drilled the outers but just used some foam in the middle to stop it rattling?


(and no, I won't blame you if in the future it falls off ;) )

cheers!

[jim.cook]

Use duct tape. :) Here in the US duct tape is used for eveything...it's the grey force that rules the world.


here's a question... :)

Basically, my CRV is a company car, and as such when I give it back in a couple of years I've got to return it to looking as it arrived.

I therefore have no qualms about drilling the 4 outer holes - when I take the spoiler off in the future I'll plug them if need be, and replace the end cap covers so that they can't be seen :)

BUT - obviously I can't do that with the centre hole :(

Has anyone who has fitted this got any thoughts on how it might work / how secure it might be if I drilled the outers but just used some foam in the middle to stop it rattling?


(and no, I won't blame you if in the future it falls off ;) )

cheers!

[Red916]

I like Duct Tape! :D

But I think it might look a tad out of place with a 4 foot strip of the stuff... LOL


Seriously though, I did consider simply sticking the spoiler on - but I'd need something which would hold it in place for 2 years (easy enough), but then be removeable without leaving a mark or taking 6 layers of paint with it (less easy :()

[Radar24]

As mentioned before Letter and 0-60 numbered bits can get really close to MM bits.
However if you want sizes that do not a good place is ENCO

Enco - Guaranteed Lowest Prices on Machinery, Tools and Shop Supplies (http://www.use-enco.com/CGI/INSRHM?DCMP=EMC-1587443)

They carry good quality imported stuff as well as the more expensive USA made Brand Name Industrial bits.

Occasionally they have free shipping. In any event their shipping is extremely reasonable for small lightweight stuff. I think the min shipping is $6.95.

-RG

[Radar24]

I have no idea what the spoiler looks like but a lot of accessories are attached with 3M double sided tape (has a translucent red film tape cover if 3M – THE BEST!). It comes in different widths and thicknesses but is very expensive in professional quantity rolls (usually 25 or 50 feet). I keep some around all the time and amortized over the 10 or more jobs it is not too bad. As long as it goes on completely clean surfaces it stays put. And no it will not lift the paint. Applying a little heat with a heat gun softens it so you can remove whatever it is you attached. Do not forget to use isopropyl alcohol as the last cleaning step or it will come off! I know from experience.

The alcohol removes any cleaning solvent residues and leaves nothing behind. They recommend using 50% but I prefer stronger 95% or even 99% if you can find it. The stronger stuff dries almost instantly after wiping. Beware on interior painted surfaces or air dried paint as it may soften the paint. If it does you will see the color transfer on the rag. Stop!!! Do not touch it again untill good and dry (hours later). Do not worry about this on base coat clear coated surfaces like on the tailgate and elsewhere in the car exterior if original, hardener is used or if baked on type paint. Original paint is resistant to just about anything. Wiping alcohol on it for a few seconds does no harm has been my experience. It is used industry wide.

There might be a reason why Honda does not use it or do they on the spoiler?
I just installed the original accessory Honda CR-V bodyside moldings. It came with the ~1/4 wide 3M double sided tape. I’ve never seen it that narrow before. Since the molding is hollow I guess that is what they had to use.

Came out nice even though it is not a perfect color match. It is just a shade darker Glacier Blue.

Good Luck!
-RG

[Red916]

I have no idea what the spoiler looks like but a lot of accessories are attached with 3M double sided tape (has a translucent red film tape cover if 3M – THE BEST!). It comes in different widths and thicknesses but is very expensive in professional quantity rolls (usually 25 or 50 feet). I keep some around all the time and amortized over the 10 or more jobs it is not too bad. As long as it goes on completely clean surfaces it stays put. And no it will not lift the paint. Applying a little heat with a heat gun softens it so you can remove whatever it is you attached. Do not forget to use isopropyl alcohol as the last cleaning step or it will come off! I know from experience.

The alcohol removes any cleaning solvent residues and leaves nothing behind. They recommend using 50% but I prefer stronger 95% or even 99% if you can find it. The stronger stuff dries almost instantly after wiping. Beware on interior painted surfaces or air dried paint as it may soften the paint. If it does you will see the color transfer on the rag. Stop!!! Do not touch it again untill good and dry (hours later). Do not worry about this on base coat clear coated surfaces like on the tailgate and elsewhere in the car exterior if original, hardener is used or if baked on type paint. Original paint is resistant to just about anything. Wiping alcohol on it for a few seconds does no harm has been my experience. It is used industry wide.

There might be a reason why Honda does not use it or do they on the spoiler?
I just installed the original accessory Honda CR-V bodyside moldings. It came with the ~1/4 wide 3M double sided tape. I’ve never seen it that narrow before. Since the molding is hollow I guess that is what they had to use.

Came out nice even though it is not a perfect color match. It is just a shade darker Glacier Blue.

Good Luck!
-RG

I feel some purchases coming on... :D

Thank you!

[NellyNel]

JWV, the most important sizes to get right is the 8mm and the 11mm, since the 3mm and 6mm are just step sizes, as I'm sure you are aware. I used 1/8 for the 3mm, 3/16 for the 6mm, 5/16 for the 8mm, and 7/16 for the 11mm center hole. The 7/16 is actually 11.1 mm, and I still had a hard time getting the jacknut in the hole. These sizes work fine.

A big THANKS to this member who posted the drill bit sizes to use (as most drill bit sets in the US are fractional sizes).

The install was easier than expected. Took me about 1.5 hours including setting up and cleaning up all supplies.

I agree with those that have said that it completes the rear end..

[MeltV]

After having a little time to really look at it now I think it would look good with any of the CRV colors as long as they also had the privacy glass (or any similar aftermarket tinting). I think the glossy black spoiler would probably stick out and look out of place without the dark and reflective back window to sit on. With the privacy glass though it actually blends in and matches pretty darn well. I'm really happy and glad I went ahead with it now :).


ron



Great idea on the black spoiler, looks terrific!

[CaptainCarl]

Thanks for experimenting with this.. I have a silver V that I was pondering the same thing about the other day.. glad you already took the plunge, looks great :)

[BugaBoo]

1.5 hours later.:)

1302

1303

1304

is that modulo spoiler?
im still undecided whether i should get mugen $800Australian dollar or modulo $500Australian dollar:) $300 difference is alot of money;)