bearing

Hello, I am new to the forum so please help me out if I am in the wrong place. I bought this CRV off craiglist last year around 62K and have been using it extensively. After some fairly rough mountain roads, I noticed a whine while driving. I initially thought it was a rock under my pad, but...

Hi guys, new to the forum here. I drive a black 2000 Manual Transmission Honda Cr-V with 276,000 miles on it. It's been making noise when the clutch is released, and the guy that I bought it from a year ago said that it was the throwout bearing. I neglected to do my own research, but instead...

Has start to intermittently make a noise. Not from engine, dropping into neutral and revving or idling engine has not effect. Braking or turning, either direction will usually stop noise. Has happened at 35mph, 60mph and 75 mph and always sounds the same. One a one hour drive it might happen...

A year ago I bought my 2006 2WD from a friend, had 88K on the clock at the time. The road noise was a little high, I thought, but my son who worked at a tire shop convinced me that the Yokohama's on there were just naturally loud. A year later the noise seemed louder than before, so I finally...

Hey guys I’m replacing the center support bearing on my drive shaft and I have taken the drive shaft and old center support bearing off but I’m not sure on how to separate the two drive shafts and take the old bearing off

Hello, I am a newbie DYIer. I have started to change my oil and filter recently. Today after the oil change, I noticed a bearing (next to the oil filter area) leaking. Took some pictures. It looks like a small leak and bearing seems to connected to a rod that goes across front wheels. Could...

Dear Helpful Honda. I have a 2012 Honda CRV EXL + Navi 2WD and last 3 years I visited Honda dealerships more than 7 times for the problem. Vehicle has currently approximately 25K miles and Honda part # 44500-T0A-A00 was replaced under warranty 3 times. There is still oil leak from passenger...

Hi, Sorry for newbie post, but dealer diagnosed my 2003 CRV needing "Replace Front Axle Bearing" at a cost of $704 + tax. Question: is the Front Axle Bearing the same as the front wheel bearing(s) or is this something different? Is there some other sort of bearing in the center of the front...

Hey guys, I am in need of do for a wheel bearing change. I do know know if I have an LX or EX. Mine is a 2002 CRV AWD, I have ABS, side airbags (says on seat not sure if actually there), 6 disc changer, NO sunroof, alloy rims, cruise control, power windows and locks. I am looking to see if...

I have a roaring wheel bearing on my 99 awd crv. I don't know how to tell which wheel it is coming from. I've seen videos of running the car with the wheels off the ground, but that seems very risky to me. Does anyone have any tips on this? Thanks

how do I get the wheel hub off my 1998 CRV to install new back plates part # 18?

On my '99 AWD CRV, w/a 5 speed....my mechanic just put in a JDM motor. When he pulled the Rt front axle (pass front) the thing would not come out of the bearing. So, it was pressed out. I bought a new Timken bearing from Autozone and a new axle from Autozone. Here is the problem, when he...

I have a 99 CRV (7th month of 98) with a 5 speed, AWD. The steady bearing/center support bearing is bad and needs to be replaced. Honda will only sell a complete driveshaft but I see a steady bearing on RockAuto....my question is has anyone had to replace theirs before? Can you replace just...

Hello all, I'm here trying to narrow down the possible causes of a noise I've started hearing recently coming from the rear wheel area of my father-in-law's 2008 CR-V EX with the AWD. The noise is louder at higher speeds, and I'm calling it rotational because it seems/sounds like it's directly...

Newbie here and thanks for your site. I am on my third CRV for my wife and plan on getting a 2013 new one for her and keeping the 2007 for myself. Don't drive the 07' much but when I did the other day thought the noise from the rear was excessive. I rotate the tires myself and when I did have...

Doing the T-belt on Saturday. I heard that there are holes in the Bearing Caps that run down through the Cams when the Engine is set at TDC. The idea is to put a Drift or Drill Bit in there to hold the Cam's position. It helps hold everything true as you swap the belt. Is this true?

I have a bad wheel bearing on the front right of my 2007 CRV. I was wondering if anyone has instructions on how to replace the bearing. Thank you in advance.

Okay so i pulled off a ball bearing turbo system off an LS (similar motor just 1.8) that made 290whp/300ft.lbs*tq and it has been looking for a new home for the past few months. My choices was between a Hatchback Civic or CRV, the choice was very difficult because there is a lot of negativity...

Can anyone direct me to some good videos showing how to replace the wheel bearings on my 2001 CRV? Thanks.

My dealer wants $536. to replace the right rear (I think they do both rears together) wheel bearings on my 2006 CRV. Does this sound like it's in the ball park? Friends are telling me to go to a local shop and get it down for way less. I could use some feedback here.