Search Results for ‘bolt’

I'm in the process of swapping out the transmission in our 05 crv. The question is about supporting the engine. The hole in the cylinder block that the bolt threads in for a support bar,. What is the bolt size? ( thread ).

This might be a silly question, but does anyone know where I can get replacement bolts for the engine cover of the k24 engine? Or maybe the exact specs of them? It’s a 10mm head

So this is kind of a twofer. We just took my fiance's car in to a local Honda dealership to have them do the airbag recall and change the oil while they're at it since i don't have time to do it right now. I was planning to try running some Engine Restore in her car, as its starting to consume...

There are arguably more aftermarket wheels available today than ever before - but how do you know which ones fit? Your vehicle requires a wheel with a specific bolt pattern in order for it to safely fit. This is determined by the number of bolt holes the wheel has and how they are spaced...

hi i have a 2016 crv trying to get location of the check bolt thanks

I just bought a used 2005 Honda CR-V. The guy who owned it before me tightened the 3 bolts way too tight, so when I was removing them one of the bolts broke. I was able to get the broken bolt out, but when I went to screw new bolts on, another bolt broke in the same position. This time, even...

I changed the plugs on my ‘02 today and noticed one of the coil packs is missing the bolt that secures it down. I’d like to replace it ASAP even though it’s been driving fine without for who knows how long, if it’s something I could pick up at a hardware store I’d definitely prefer that to mail...

I'm changing my transmission and haven't really seen to many torque specs around can anyone please tell me how much torque does an automatic torque coverter bolt take.

This may sound trivial. I was looking under the car today. I took delivery on Wednesday. One of the bolts holding the rear sway bar, left bushing is completely corroded. It almost like the bolt was defective and not corrosion treated. I was going to call the dealer tomorrow, and see if...

2011 CR-V SE, replacing front and rear disc brake pads + front strut dust boots

Hey everyone! This is my first post here, I’m excited to be a part of the community. As I was filling the wiper fluid in my 2011 CR-V the other day, I noticed the bolt attaching the top of the wiper fluid reservoir was missing. Does anyone know the dimensions of the bolt and how I can get a...

Thought it was be a simple process to remove the rear trailing arm and replace the bushings. Got all the bolts removed but one. Head snapped right off. Guess Ill be pulling the whole rear assembly and cutting and drilling out the remainder. i had to bend the small plate that was blocking...

Hey All, I have a 2012 CR-V, and just did the rear-differential drain / fill. After the fact, I realized I inadvertently put 20mm crush washers on both the drain and fill bolts. That size is correct for the fill, but the drain should have been 18mm. All seems to have gone well, and it doesn't...

We found this metal bolt under our 2007 Honda CRV (4WD LX) in the garage. It's a carriage bolt, also described as a round head square neck bolt (though threaded all the way), 24 mm long (not including the head) and 9 mm in diameter. We've looked under the car and can't seem to find anything...

Part 17, there are two different bolts listed: 90119-S6M-Z01 BOLT, FLANGE (16X62) 90120-STK-000 BOLT, FLANGE (16X62) (SERVICE) Can anyone tell me the difference between these and what (SERVICE) might mean? The Honda parts counter guys couldn't help me...they had no clue.

Hello All, In the process of the changing the rear struts on my 2007 CRV, and I've run into a problem. Went to remove the two trailing arm bolts on the right side to drop the arm. Got the front bolt out no problem, but the rear bolt seized after coming out about 1/2 an inch. Guessing the rusty...

Here is the test subject with measurements. Planning to port and polish since there is not a lot of aftermarket support. So I made my own. I have experience doing i4/v6 accord runners so these should be fairly easy. Only thing that is annoying is pulling off the injectors and making sure that...