Search Results for ‘bolts’

Hello all, I was going over my 2002 CR-V when I saw some of the front bumper bolts and clips were missing. Headed to youtube and found they are 8mm and 10mm. My question is what 8 & 10 mm? 8x21 10x30, I haven't found a clear answer. I did look at Honda Automotive Parts, but did'nt see what...

I have replacement passenger seat that I want to swap into my 2003 CRV, can someone tell me the best way to remove the plastic trim coving the bolts. I looked at it a bit and can't quite figure out how to remove the left front bolt cover. I don't want to break it if there is a trick to it.

Does anyone know the size of the torx nuts for the roof rails?

2007 LX fwd - need ideal alignment spec w/ new struts, camber bolts & camber struts Greetings all :) I just replaced all my struts and added front camber bolts (upper hole bolt) and rear adjustable camber upper tie rods. In addition to a toe adjustment Fr & R I can now get the camber spec to...

2007 LX fwd - need ideal alignment spec w/ new struts, camber bolts & camber struts Greetings all :) I just replaced all my struts and added front camber bolts (upper hole bolt) and rear adjustable camber upper tie rods. In addition to a toe adjustment Fr & R I can now get the camber spec to...

I'm currently replacing rear hubs and bearings. Got everything apart except I couldn't get the rear aligning cam bolt out of the bushing. It must be seized. I was going to cut it, but I can't find them online? Are they actually cam bolts? Or can I use a standard bolt? I took the nut off and...

Wanting to lift the rear of my gen 1 to even out the height with the front. Any of you guys put a spacer without having run extended top hat bolts ? What's the biggest we can go ? Thanks

SOLVED: MY14: Stock Running-board Installation: Flange Bolts Too Tight I'm installing stock running boards and having issues threading the flange bolts for the brackets into the holes on the chassis. I have verified they are the correct holes (kind hard to miss them), and the diameter and...

I let a friend of my youngest BIL start the process to change out the starter on my daughters 2005 V. While taking off the intake manifold he managed to round out two of the 18mm bolts that keep the manifold attached to the head/block. I asked him to stop as he didn't have the extraction tip...

Security Torx bit bolts for OEM Load bars / Crossbars Sorry if this has been asked before but I can't seem to find the answer. I'm looking to purchase Security Torx bit bolts that are the same thread and length as the ones included w/ the OEM Load Bars / Crossbars p/n 08L04-T0A-100 Basically...

For the life of me I haven't been able to find a reasonable set of replacement head bolts for my 2000 CRV, aside from the OEM ones that go for about 20 bucks a piece on amazon. There are, however, cheapo ones on amazon and ebay that claim the 90-01 Integra bolts will also work with the CRV. I'd...

I am trying to remove the splash shield but it has these bolts, that I do not know how to remove. Can someone guide me in the right direction to remove these bolts? It is Part Number: 90143-TL0-000 Part #19 in the image...

I'm replacing the head gasket on a 2000 CRV and the manual calls for replacing the exhaust manifold bolts and nuts. Is this really necessary, and if so, is there a good source other than the dealer? Ken 2000 CRV-EX

Hi all, Just bought a Curt 13555 from Ebay and realized that it did not comes with the hardward. According to the installation manual, it needs the following: 4 pieces of M10 - 1.25 x 30 Hex Bolt 4 pieces of 7/16" CONICAL TOOTHED WASHER 1 piece of 7_16 - 14 x 1.75" x 1.00" C-C U-Bolt 2...

Hi I love my CRV. I leave in NYC. about 2 months ago I Saw that the door bolts on the inside of the door hing are rusting. the car is not even a year old. did anybody else experience this problem. Thank you.