bushing

So long story short, drove over a hump that was higher than my CRV’s (5th Gen) clearance and got some of the undercarriage in contact w/ the ground. Checked my car later and saw the front compliance bushing was leaking. First time owning a CRV (and a new one at that), is that an expensive...

I am getting ready to rebuild a rear strut on my 2000 CRV SE. Does anyone know what size cup or socket I will need to drive the bushing into the shock? It has to be a cup or socket because of the way the bushing is made - I had to order the bushing from the California parts depot and I want to...

Not sure what it's called, or what it does (educated guess in the title), but there's a hockey puck on the front axles on daughter's car. The puck is no longer attached (just dangling on the axle). CVs and boots in great shape, so seems a shame to replace the whole axle just because of the puck...

Hey, so I live in a sort of hilly area with bumpy roads (not ridicolous but constant tho). When I turn right corners the crv doesnt make a full turn. If I turn and hold the steering, it pushes its front out and then comes back in 3/4 way of the turn. Pretty awkward, but anyway I can get that...

I was changing the oil yesterday and I saw condensate water dripping directly on the lower control arm bushing. The water runs down the circular bushing and pools at the bottom, and appears to seep into the bushing itself. There appears to be corrosion forming in the bushing at the bottom as...

How difficult was it? How much did the bushings cost? Any special tools required?

I looking for a rear trailing arm bushing for my '04 . I found the others on this website... .https://www.hondapartsnow.com/parts-list/2004-honda-cr-v-5dr_ex_4wd-ka-4at/rear-lower-arm.html I don't want to start replacing them unless I have all the bushings. It seems like it's part of the...

Hello Everyone I just noticed that one of the rear trailing arm bushing is busted. I know these chassis share parts with Civic and Integras. Does any one knows the size of the rear trailing arm bushings? I am considering energy suspension for the RTAB tia

I have a 99 Honda CR-V that has hit the point to where I need to get my bushings replaced (see below). I picked the car up this past summer with approx 205K miles on it. I've since been working my way though some repairs. I believe the bushings need to be replaced as any bump hit, or corner...

Hi there, still the original owner of a 2000 EX (Milano Red) 278,000 miles on it. Need to eek out another 6 months or so! Long time member over at HondaSUV.com- those guys over there really helped me keep this car alive all these years. Alas, that site seems to have been sent to the big...

I don't know much about the RTA suspension on my G1, but when Doing a 4 Wheel Alignment I noticed a few problems: 1: Rear Passenger-Side Tire is an extra 2mm Toe-In. 2: Passenger-Side RTA Bushing is deteriorated. 3: The outside edge of the tread is worn more than the rest of the tire. 3 made me...

Recently had some recall work done. Dealer (stealer) told me my compliance bushings are cracked. Wanted in the neighborhood of $600 to replace. Told him to shove it. I looked under the car and located what i THINK are these bushings, which look fine to me. Also in waiting room heard them...

I'm planning to replace the front LCA Compliance bushing. Before I crack the bolts lose, what are the torque specs for the nut/bolt for the front and rear bushings, and the balljoint on the knuckle. Thanks.

My wife's 2002 CR-V EX with 125,000 miles on it is making a creaking noise when you bounce on the rear bumper. I thought for sure it was strut/spring noise so I replaced the rear struts today with Monroe complete EZ-Struts that I got for $228 delivered from PartsGeek.COM. It's much quieter and...

I need to replace both rear trailing arm bushings on my '99 LX Are there any members here from Honolulu, HI who own this tool and are willing to rent it out? Of course, I am prepared to pay a reasonable rental fee and to leave a refundable security deposit. I will be needing the tool for just...

i have a 2005 CRV, how can i be sure if these two rear trailing arms comes out, can they be changed and how? specially with the two round flanges which make it hard to get it out ... hope to get some help and photos :confused:

Can someone suggest after market part numbers ? I googled with no luck :-(.

Looking to buy a trailing arm bushing remover for a 1999 crv. Thanks

Is there anyone on the forum who rents out this tool. I need to change both bushings due to serious cracking. I live in NC Thanks

I replaced my sway bar bushings yesterday evening. Very easy project. To do front and rear it was less than an hour. I replaced the stock bushings with Moog bushings from Rock Auto. The replacements were rubber on the rear and the fronts are a composite. I would have liked to have done...