Honda CR-V Owners Club Forums banner

bushings

  1. Tires, Wheels, & Suspensions
    Hi guys (and gals)! I recently replaced the infamous trailing arm bushings on my daughter's 99 CRV. There was some confusion about the depth these bushings have to be pushed in. The older ones were pushed to 17mm above the outside arm surface, but a TSB that I found about replacing these...
  2. Gen 1: 1996-2001 (UK 1995-2001) CR-V
    Recently I was on a fire road and made a U turn it a turn around and while I was turning the trailing arm bushing, on my rear passenger side, slipped out of my trailing arm. This left my wheel with room to play in 4 directions so I parked it for the night. The next day I I went back out to the...
  3. Tires, Wheels, & Suspensions
    I replaced my front stabiliser bushings on a Gen 1 Crv and I noticed the part of the stabiliser bar where the bushings are attached/the bar pivots are quite rough/pitted/corrosion. I'm assuming leaving them like that may accelerate the wear of the new bushing, should I be cleaning up the...
  4. Gen 3: 2007-2011 (UK 2008-2012) CR-V
    My CR-V (tan) has had a strange sound from the front since I bought it, and only when leaving the driveway. Nothing seems loose, the stabilizer bar connectors are all intact, etc. But it has been minor enough that I haven't bothered to track it down. The blue CR-V, though, has a knock in the...
  5. Tires, Wheels, & Suspensions
    I'm currently replacing rear hubs and bearings. Got everything apart except I couldn't get the rear aligning cam bolt out of the bushing. It must be seized. I was going to cut it, but I can't find them online? Are they actually cam bolts? Or can I use a standard bolt? I took the nut off and...
  6. Performance Modifications
    Anyone know of good (or ANY) shifter bushings for a 2006 CRV?? I've looked around the internet and found nothing. Doesn't look like anyone makes them specifically, but I wonder if anything from another vehicle might fit it?
  7. Maintenance and Service
    Hi. Trying to help my dad out with his 05 CR-V. Sway bat bushings are toast. Getting that clunk. I measured his front sway bar and it is like a little over 27mm I have not seen any specific polyurethane bushings available for this year. Anyone running some poly say bar bushings on a 05?
  8. Maintenance and Service
    Hey everyone. I seek advice... So I have a 1997 cr-v with 215,000 miles on it. This thing has been great. I just replaced the timing belt. No signs of any fluid leaks. I recently replaced the sway bar end links to eliminate that knocking sound I had assumed was something much worse after my...
  9. Maintenance and Service
    Hi, A couple years ago a mechanic told me I should replace my bushings and/or the link sways (I can't remember what as I just ignored his recommendation). Anyhow, a couple yrs later only on very low speeds I am noticing some noise from my rear end (And it isn't from fibre). Anyhow, how do I...
  10. Problems & Issues
    Please refer to the picture below. My V has ~100K miles. I am doing rear suspension work and these bushings are accessible for replacement, if needed. I have few questions. Q1: I have already bought OEM part (ref in picture HAB-004). Should I replace them ? The old ones look okay to the...
  11. Tires, Wheels, & Suspensions
    Okay, we have a 1996 Honda CRV (It is a Japanese import) Here is the problem though, we live in Mozambique, and the roads here are a bit less than up to par... I am wondering though if there is an upgrade for the lower control arm to strut wishbone bushings. Due to our roads we have been having...
  12. Problems & Issues
    Hello, I purchased my first Honda in 2011, it was a 1998 CR-V EX 4WD Automatic with 254,000 Km's on it. It was very well maintained just had a new timing belt and windshield replaced so I went for it. Since then I have put almost 30, 000 Km on it and have been very happy. No real problems to...
  13. Maintenance and Service
    Has anyone replaced these themselves? The outer bushings in front of the rear tire are beat out. Honda here in Nova Scotia says that the trailing arm is not serviceable and the arm needs to be replaced. Very costly. I don't believe this is correct as I have found some aftermarket bushings...
  14. Problems & Issues
    So I'm a newbie here. I have a 1999 CR-V with 138K miles on it. The CR-V was making a light squeaking noise when letting up off of the brake, and after research I found out that it was the brake shoes squeaking against the backing plate when I released the brake. So I had a friend of mine that...
  15. Problems & Issues
    All, Lots of searching but I haven't seen an answer yet. Had my '99 CR-V EX up in the air a few days ago and found some pretty bad wear on the inside edge of both rear tires. For the most part the tread wear is even across the width of the tire but the inside edge is worn almost like a...
  16. Problems & Issues
    I am looking for rear lower control arm bushings for my 98 crv. When I was doing my suspension and replacing parts I found out that the rear lower control arm is loose. This probably is what causes my car having alignment issues. The whole part is expensive. Are there any bushings that will fit...
  17. Tires, Wheels, & Suspensions
    This is both sides of my 2005 CRV. Is this normal for 106,000 miles or other people have same experience?
  18. Problems & Issues
    I have a 1997 CRV with 245k miles that needs to have the front sway bar endlinks and bushings replaced. I am trying to figure out exactly what parts will be needed. I will not be doing the work but will probably give the parts to someone to do it. If I got with OEM do I need parts 2 and 4...
  19. Problems & Issues
    I have a 99 CRV LX all wheel drive and I need rear sway bar bushings but cant find them anywhere on the web. Does anyone know where I can order them online? I also heard that most of the time when replacing the bushings the bolts will break off. Any tips on this and if they do what is the...
  20. Maintenance and Service
    I noticed that my differntial bushings have cracked and need replacement. I am not sure how to go about replacing them and i tried to find replacement bushings if there are any, but i havent been succesful. Just some direction would be helpful
Top