Honda CR-V Owners Club Forums banner
  • Hey everyone! Enter your ride HERE to be a part of October's Ride of the Month Challenge!
pins
1-12 of 15 Results
  1. Gen 4: 2012-2016 (UK 2012-2017) CR-V
    In wanting to accomplish some changes on my 2014 Honda CRV. I noticed some of the original Push Pins holding the plastic panels together underneath the car had some broken legs when removed. They appeared as never pulled before. Would be nice to replace with new pins. The cost at the Honda shop...
  2. Gen 4: 2012-2016 (UK 2012-2017) CR-V
    Hi there, Can you please check this information is correct? Front - Caliper 101 FT LB Front - Caliper Slider Pins 36 FT LB Rear- Caliper 80 FT LB Rear- Caliper Slider Pins 16FT LB
  3. Gen 4: 2012-2016 (UK 2012-2017) CR-V
    Hi, 2014 CRV Front brake caliper have two different pins model: Does somebody know their correct position... Which one goes up ? Thanks,
  4. Gen 3: 2007-2011 (UK 2008-2012) CR-V
    Had the car in for some service this morning. As a precaution asked them to lube the pins while the wheels were off for a rotation. Told me it's $129.00 since they have to disassemble the brakes. Not sure it's true but I don't know whats involved. I know on my CX-5 the dealer did it for free...
  5. Gen 2: 2002-2006 (UK 2002-2007) CR-V
    I pull apart the brakes on my 05 CRV LX every spring to clean and lubricate the slide pins, pad retainers and contact surfaces between the pads. Last year I had a very difficult time removing the front lower slide pins from the caliper mounting brackets. The pins were corroded so I went ahead...
  6. Gen 1: 1996-2001 (UK 1995-2001) CR-V
    Deciding to check the rear brakes as I have to get a roadworthy check done, I managed to force the first drum off. I am new to Honda cars in general and have never seen such a ridiculous set up. Now there is a rubber gromett plug ...in fact two, but one is a blank...which I removed to, well in a...
  7. Gen 3: 2007-2011 (UK 2008-2012) CR-V
    I tried to search for this, but there's a million posts on brakes but I didn't see any that discussed this questions specifically... Went to rotate tires for the season but they were welded on but good, so let the dealer beat them off and they can check the brakes while they're at it. Turns...
  8. Miscellaneous / General CR-V Discussions
    The service manual specifies to use Honda Silicone Grease (08C30-B0234M) on the caliper slide pins. However, this stuff is about $50 a tube and not widely available. Are there any good alternatives? I've read that only silicone grease should be used because it's compatible with the rubber...
  9. Gen 2: 2002-2006 (UK 2002-2007) CR-V
    Many of the Honda vehicles have the same type of brake caliper guide pins. For most , the top and bottom guide pins are different. For our Honda CRV ( 2005) the bottom guide pin is round and the top is basically a round pin with three lengthways flats...
  10. Gen 2: 2002-2006 (UK 2002-2007) CR-V
    2002 Honda CRV EX. I did the front brakes today. Last time I did them was about 50K miles ago. I always clean everything real good and use the brake grease on the pins and parts that contact the pads. One of the caliper slide pins was pretty frozen in the bracket. I put the bracket in a vice and...
  11. Accessories
    In the upper-left of the fuse box of the 2009/2010 CR-V, there is a 6-pin connector for accessories (like the Honda self-dimming rear view mirror accessory). Can anyone please get me a diagram showing what each pin is used for? Here's why... I want to buy the Honda self-dimming mirror harness...
  12. Gen 2: 2002-2006 (UK 2002-2007) CR-V
    My wife's 04 CRV has been making a hard popping noise when braking on occasion. Well come to find out a caliper pin was supposedly frozen due to rust. Well it was taken out and cleaned off by the mechanic and lubed but it started doing it again. So this time I took off one caliper and to my...
1-12 of 15 Results
Top