replacing

I got a message saying that my post had been moved.....not sure why, so I am reposting. We are replacing the compressor, condenser, condenser fan, evaporator, expansion valve and hoses on the vehicle. Can anyone point me to directions on accessing the evaporator/expansion valve? Can I get to...

We are replacing the compressor, condenser, evaporator, expansion valve and hoses on the vehicle. Can anyone point me to directions on accessing the evaporator/expansion valve? Can I get to them by taking out the glovebox and blower assembly? thanks, Dale

I have a 2012 AWD with 118K miles on it, and the front wheel bearings need to be replaced. The dealer's estimate was $1376. $1000 of that is labor. I have a decent set of tools and I do a lot of my own car work, and I'd like to save that $1000 labor by doing it myself, but I'm not sure if I...

Maybe it is getting use to this Maintenance Minder but it has yet to go off or signal me on anything. I took it in for it's last freebie oil change at 15,400 miles and they deemed that according to the maintenance schedule it was due for a rear differential fluid change at 16K so go ahead...

Going to tackle this tomorrow with some of the replacement KYB Struts Plus they recently started making for this Gen.3 CRV (KYB SR4233 & SR4234) I got my instruction from this A1 Auto video. I need to know if his torque values are correct (all in ft.lbs)... 5 top bolts under the hood, 33 2...

2017 crv ex-l took 2 bolts out of lens on tailgate cannot get the lens to remove to replace bulbs. How to i replace the bulbs remove the plactic panel on the hatch?

Newbie - replacing engine 2006 CR-V Kevin in Minneapolis. Just bought a 2006 CR-V, needs a new engine. Trying to figure out if way to identify engines visually - some have I-VTEC on valve covers, mine does not. Also, can't find the engine ID number. Thanks, orrenz1917 at g mail

Hi guys, I'm new here. Not sure this is the place to post this or not but please let me know if it isn't. So what happened was my wife accidentally drove on a tree stump last week, so it damaged the inner liner on passenger side, specifically the part right under need the fog light/bumper. I am...

I replaced my front stabiliser bushings on a Gen 1 Crv and I noticed the part of the stabiliser bar where the bushings are attached/the bar pivots are quite rough/pitted/corrosion. I'm assuming leaving them like that may accelerate the wear of the new bushing, should I be cleaning up the...

OK thanks for offering to answer our questions... Here is a simple question... My wife owns a 2003 Honda CRV base model and we are soon to trade it in for a newer model. We may need to install a new catalytic converter in the short run before we trade in the car. The car is now set up with...

Hey Folks I have a dead TPMS sensor on a 2007. I purchased an Autel MX-Sensor and am going to put it in shortly. The Autel manual states the sensor weighs 18.5g with the valve stem. I'd like to do this without having to rebalance the wheel, so I need to know what the OEM sensor weighs. That...

Is this a difficult job to do? And what kind of prices should I look to be spending on these parts? Looking on the internet, I’ve seen everywhere from $27 an injector, up to $300. I want to make sure I’m getting some that works properly without having to pay crazy money for them. It’s a 2001...

I finally found some KYB Strut Plus for the front end of my 2009 LX. What other parts should I have on hand when I start to replace them to insure I won't be doing the job twice? Bushings or other suspension parts? thanks, Rob

Our CRV is starting to have intermittent air. We are a year outside the extended warranty. When the air fails to come on I can clearly see the clutch not engaging. If I tap it, it engages. Was going to either replace compressor or get new ac clutch and coil. It appears to replace the ac...

Hope this is not a duplicate As we all know the OEM dip stick has a yellow measuring device. I have viewed two Honda videos regarding the oil/gas delusion issue. In both videos Honda displays a conventional dip stick. Would it be to my advantage to replace my new yellow measuring device...

Hello- I'm trying to replace a lock cylinder (driver's door) on a 2012 CRV LX. I'm to the point where I need to disconnect the old cylinder from the door handle. It's damn near impossible to see what how to disconnect it. I have the vapor barrier peeled back so I can get to the lock but I can't...

I replaced the fuel pump / sending unit and the new one did not come with a new seal so I used the old one and now it is leaking from that seal. Either the seal is bad or the lid is not screwed on tight enough. I did not have the special tool so I after hand tightening I tapped it with...

I have to replace a broken wheel stud on the right front of the 2008 CRV. The stud was crossed-threaded and the stud had to be torched out to get the wheel off to replace the rotors and pads. The problem is I don't know how to get the hub off to remove and replace the bad stud. Rather that...

Hi gents, spent a couple hours searching the forum to no avail, so figured I'd might as well post a thread. I'm looking at replacing the entire receiver in my 2014 EX-L w/Navigation. Does anyone know what work I'll need to do myself for the camera connection? Seems like it's quite rare for...

Hi from the UK! The head unit screen in our 2016 CRV got damaged recently so have found a replacement like for like unit online, my question is, once this new unit arrives and it gets plugged in, am I going to have an issue with the car recognising it (do I need to enter the VIN number/radio...