Honda CR-V Owners Club Forums banner

screw

  1. 02 CRV MT clutch snap sound looks like master cylinder popped a screw, split leaked

    Problems & Issues
    02 CRV MT clutch snap sound looks like master cylinder popped a screw, split leaked This just happened to me 1 hour ago. 2002 CRV MT. car off. push clutch down. snap/pop sound. noticed the clutch master cylinder has slight split apart. at one of the 3 screw points (triangle shaped) one screw...
  2. Screw for windshield washer reservoir?

    Problems & Issues
    Any idea what screw is needed to hold the 'top' part of the windshield washer reservoir? I just noticed the one on my 2007 is missing and the top plastic piece is loose...not sure how!
  3. Oil Filter Under Cover Screw Stripped

    2012-2016 Official Specs, Features, Etc. (Gen 4)
    While getting ready to do an oil change, I noticed one of my oil filter under cover screws is stripped. The head of the phillips screws seems to be made of plastic. Any recommendations on how to remove it? I bought this car CPO from a local Honda dealer in 2016, and I believe it was serviced...
  4. Rear hatch striker top screw - FYI

    Interior
    I can't believe I still have my 2002 Honda CRV - but it keeps going! Here is an FYI for the door striker top hatch screw: It gets loose but please don't let it fall off!!!! It is attached to a rear plate that can rotate/swivel. If the top and lower screws get loose and one falls off like it did...
  5. New splash guard screw seems stripped?

    Exterior
    Hello everyone! Wife got a new 2018 CRV EX about a month ago and I finally got around to installing the splash guards. Everything seems to have gone fine, except one screw does not get as tight as the rest. it's the top screw of the front driver's side guard. This is the one you puncture...
  6. Distributor rotor retaining screw size

    Problems & Issues
    2000 ex Oddly the old rotor was some style that had no screw thus I don't know what to replace it with 5x12 appears not to fit. And Honda dealer has none in state!
  7. ATF Drain and Fill - Big time screw up

    Maintenance and Service
    Hi guys: I think I cross threaded the trans drain plug on my 09. I replaced the crush washer, and did not over tighten, but someone I screwed it up anyway. Now I have a pretty good leak from the drain plug. There is a gap between the "block" and the crush washer - I stopped tightening at...
  8. 2017 CRV EX a screw fell down from behind the dashboard

    Problems & Issues
    Dear all, I was driving my CRV and suddenly a screw fell down from behind the dashboard. I was able to hear the sound as I was driving at a constant speed around 60mph with no traffic. When I stopped the car, I found a screw under the break pedal. As I was able to hear it bumped into several...
  9. 2004 crv air box screw seized

    Maintenance and Service
    Was going to replace the air filter on my recently purchased crv but one screw on the air box is rusty and seized it is a Phillips screw that also fits a 5/8 socket but the screw is rounded off and rusty, does anyone know a way to remove it
  10. the screw on the splash plate under the engine oil tank of 2013 CRV

    2012-2016 Official Specs, Features, Etc. (Gen 4)
    When I change oil, I broke one of the four screws that hold the splash plate for the oil tank. Anyone knows where I can buy a replacement screw? It has to come with a U shape clip. Thanks.
  11. Caliper bleed screw sizes?

    Maintenance and Service
    I'm trying to switch out the brake bleed screws on my 2014 cr-v LX but I can't find the screw thread size and length anywhere. Do any of you know where to find detailed info like that or if you know off hand let me know. Reason is I'm trying to install speed bleeders. Thanks in advance
  12. front plate screw size.Could someone please tell me what sizes are the two different

    Problems & Issues
    I'd like to know the two different screw sizes to mount a plate to front plate bracket of 2006 crv ex. Also, is there a way to increase the volume of turn signals, dash alerts, alarms, warnings, head lights on warning, etc. Appreciate any help.
  13. Valve Adjustment Screw wont go far enough!

    Problems & Issues
    Hello all, Halfway through my valve adjustment (01 CR-V SE) the exhaust lash adjuster won't unscrew enough to reach spec. All of the other lashings have been adjusted without issue. I can't possibly imagine why, or how this is possible. Anyone else experience this or have advice? 2.0L 4...
  14. By the Grace of God I Am Here.... TIRE SCREW UP Need Advice

    Tires, Wheels and Suspensions
    Well known tire company installed one tire on my CRV EX Jan 2015 that was damaged beyond repair due to a road hazard. The tires were only a year old and I did not purchase them from this company. I did not purchase extended road hazard insurance from the company where I purchased the tires. I...
  15. License plate (rear) screw stripped

    Problems & Issues
    One of the screws for the rear license plate on my 1998 CRV is stripped. I can't figure out an easy fix - any suggestions?
  16. Key Fob screw removal question

    Problems & Issues
    The little screw appears to be stuck (2005 CRV) and I am afraid I am going to strip out the head like I found my other one today. Is there a trick to doing this or should I bring it somewhere thanks for any info
  17. Rotor set screw missing

    1996-2001 Official Specs, Features, Etc. (Gen 1)
    I've got a 98 5 speed manual. I am replacing plugs, wires, distributor cap and rotor. Everything went fine till I got to trying to remove the old rotor. There is supposed to be a Phillips Head set screw holding the rotor on the shaft. But there isn't isn't. The rotor appears to be held on by...
  18. Beware my friends, don't screw up like I did.

    Problems & Issues
    Was replacing my wiper blade inserts today, when Boom, cracked windshield. :mad: My fault, :o the passenger side wiper arm slipped out of my hand, when the blade came off and the bare metal bar smacked the glass. I'm a little shocked & upset that it cracked it from a height of only 5-7 inches...
  19. 2008 CRV Door actuator mounting screw

    Problems & Issues
    So I've removed my actuators in the past with no problem. Had to replace one this weekend but one of three mounting screws is going to need drilling out. I can't seem to find the size screw listed anywere so I can get some before I proceed . I think it's a phillips M6- 14 x 1.0 is that correct?
  20. 2009 CRV License Plate screw size

    Exterior
    Hey guys, Does anyone know the screw size for the back (or front) license plate? I'm getting some new stainless steel frames and the screws that are there now are covered in rust. If anyone knows the size or has a link to a site that sells the screws would be great. Thanks in advance for any help!
Top