Honda CR-V Owners Club Forums banner

screws

  1. Engine splash cover screws

    Problems & Issues
    Does anyone know where I can get the flat head screws used on the 2017 crv engine splash guard? It uses several wide flat screws (phillips head) as well as some 1/4 turn slotted screws to hold it on. You would think they would stick with either all slotted or all phillips. Been searching the...
  2. Hail Mary request -gen 1 roof rails screws

    Racks, Hitches, & Towing
    All, I scored huge today at the upull yard and got an oem roof rail system for $13. It had every damn piece EXCEPT the 12 Phillips used to hold the rails to the mounts. Does anyone have these or have a source!? TIA Sent from my iPhone using Tapatalk
  3. New License Plate Frame that comes with Nylon - Plastic Screws- Beware!

    Problems & Issues
    Please be very careful installing plastic screws that comes with License Plate frames. Mine broke in half while tightening the screws. I had to drill and remove the broken screw. Used another bolt this time.
  4. Ignition Coil screws

    Problems & Issues
    I'v been troubleshooting problems on my 2000 Crv and I purchased a new ignition coil. In the process of trying to remove the old one, I began to strip one of the screws holding the coil in place. My new coil didn't come with replacement screws. How can I get it out and is there somewhere I can...
  5. 2011 CRV Roof Rack Install - Removing Paint from Screws

    Racks, Hitches, & Towing
    I am about to install the OEM crossbars on my 2011 CRV and dread having to remove the paint from 8 screws by threading and unthreading the special nuts several times (per screw). I kinda started on that today and it' s going to be a huge pain. Are there other ways to remove the paint, or at...
  6. 2011 EX-L 4WD License plate screws

    Accessories
    For those who want to use security screws for their license plate holders here is what I used: Rear http://www.ebay.com/itm/Stainless-License-Plate-Security-Anti-Tamper-Theft-Screws-M6-Import-Snap-On-T27-/231464490336?vxp=mtr Front...
  7. what size screws mount shutoff valve to charcoal canister

    Problems & Issues
    Hi folks...newbie here, at least to this forum. I've got a faulty vapor canister shutoff valve - due, no doubt, to rust that's given me an air leak. But to get the shutoff valve and solenoid off, I had to cut the heads off the rusty screws... and the plastic molds that hold the nuts are no...
  8. Rotor retention screws

    Maintenance and Service
    Hello, new owner of a 2003, new to forum. I was rotating tires this weekend when I notice the rotor retention screws are missing on my rear rotor. How concerned do I need to be? Do these screws only serve to hold the rotor on when the wheel is removed? In other words, with the wheel bolted on...
  9. Screws that hold Splash Guards

    Gen 3: 2007-2011 (UK 2008-2012) CR-V
    Hey Guys, I have 2009 CRV and yesterday I accidentally went through a pile of snow/ice. After hearing noise when making right turns I noticed that the front passenger side splash guard was halfway off and one of the screws was missing. Does anyone know where I can order that particular screw...
  10. 1st DIY oil change 2012 CR-V: cannot remove four (4) Phillips screws holding cover

    Gen 4: 2012-2016 (UK 2012-2017) CR-V
    April 6, 2013 Greetings: I'm an automotive DIY'er and have always changed the oil and oil filters on my vehicles. Today, my first attempt to change the oil and filter on my 2012 CR-V (purchased in August 2012) met with failure. (This would have represented the vehicle's first oil change.)...
  11. 2000 CR-V Glovebox Latch Assembly - What Type of Screws

    Problems & Issues
    The latch assembly to the glovebox fell out and the screws are missing. What kind of screws/nuts should I replace them with? PM pls
  12. 2007 Front License Plate Screws

    Accessories
    Does anyone have the specs for the FRONT license plate screws for a 2007 CR-V ? I'm looking to replace them in stainless steel. Thanks in advance for your help ! ~Howard
  13. Honda Dealer Rip Off for Key Fob Screws

    Gen 2: 2002-2006 (UK 2002-2007) CR-V
    Late last week we took our 2005 Honda CRV in for it's 65,000 km maintenance. At the same time we also requested that they change the batteries on the key fob because neither we or our jeweler were able to get the screws out. We ended up mangling them so we asked the dealership to do this...
  14. rotor retaining screws

    Maintenance and Service
    The two retaining screws on my front rotors for a 03 honda CRV are stuck. I even used an impact driver (hand held - hit with hammer type) on it. No movement. I've heard folks "drilling out" the screws. Does this mean you guys are using a screw extractor set, or does it mean you're simply...
  15. Remote-Key Fob Screws

    Maintenance and Service
    Hello: Recently I replaced the batteries in two remote-key fobs for my 2005 Honda CR-V. Perhaps the screws were installed using "Lock-Tite" or a similar adhesive, but they were painfully difficult to remove. Eventually resorting to "strong-arm" methods, I nearly stripped the heads of both...
Top